J'ecris dans une EEPROM 24c08 jusqu'a l'adresse 996.
Le prob c'est que quand je li se que j'ai ecris ca ne me donne pas les meme valeur s.
Code : Tout sélectionner
Ici j'ecris de l'adresse 6 a 996 .
void Affichage_Send_Vr()
{
Send_Uart_Ray_VCons();
for(adr = 6 ; adr <997;adr = adr+4)
{
Conv_AdcToASCII(2);
LCD_Chr(2,7,VReel[1]);
LCD_Chr(2,8,VReel[2]);
LCD_Chr(2,9,',');
LCD_Chr(2,10,VReel[3]);
I2C_Start();
I2C_Wr(0xA2);
I2C_Wr(Adr);
I2C_Wr(VReel[1]);
I2C_Wr(VReel[2]);
I2C_Wr(VReel[3]);
I2C_Stop();
Delay_ms(50);
}
La je lis les meme adresses .
for(adr = 6 ; adr <997;adr = adr+4)
{
Conversion4(Adr);
Soft_UART_Write(Tampon[1]);
Soft_UART_Write(Tampon[2]);
Soft_UART_Write(Tampon[3]);
Soft_UART_Write(' ');
I2C_Start();
I2C_Wr(0xA2);
I2C_Wr(adr);
I2C_Repeated_Start();
I2C_Wr(0xA3);
Soft_UART_Write(I2C_Rd(1)); //Lecture et envoi Envoi RS232
Soft_UART_Write(I2C_Rd(1));
Soft_UART_Write('.');
Soft_UART_Write(I2C_Rd(0));
I2C_Stop();
Soft_UART_Write(' ');
Soft_UART_Write('c');
Soft_UART_Write('m');
Soft_UART_Write('/');
Soft_UART_Write('m');
Soft_UART_Write('i');
Soft_UART_Write('n');
Soft_UART_Write(10);
Soft_UART_Write(13);
}
}
C'est un echantillon de mon programme ne soiyez pas etonné si vous ne voyais aucun declaration de variables et de fonctions.
Avec se code je n'obtient pas les bon résultats , alors qu'avec celui ci oui :
Code : Tout sélectionner
void Affichage_Send_Vr()
{
Send_Uart_Ray_VCons();
for(adr = 6 ; adr <997;adr = adr+4)
{
Conv_AdcToASCII(2);
LCD_Chr(2,7,VReel[1]);
LCD_Chr(2,8,VReel[2]);
LCD_Chr(2,9,',');
LCD_Chr(2,10,VReel[3]);
I2C_Start();
I2C_Wr(0xA2);
I2C_Wr(Adr);
I2C_Wr(VReel[1]);
I2C_Wr(VReel[2]);
I2C_Wr(VReel[3]);
I2C_Stop();
Delay_ms(50);
Conversion4(Adr);
Soft_UART_Write(Tampon[1]);
Soft_UART_Write(Tampon[2]);
Soft_UART_Write(Tampon[3]);
Soft_UART_Write(' ');
I2C_Start();
I2C_Wr(0xA2);
I2C_Wr(adr);
I2C_Repeated_Start();
I2C_Wr(0xA3);
Soft_UART_Write(I2C_Rd(1));
Soft_UART_Write(I2C_Rd(1));
Soft_UART_Write('.');
Soft_UART_Write(I2C_Rd(0));
I2C_Stop();
Soft_UART_Write(' ');
Soft_UART_Write('c');
Soft_UART_Write('m');
Soft_UART_Write('/');
Soft_UART_Write('m');
Soft_UART_Write('i');
Soft_UART_Write('n');
Soft_UART_Write(10);
Soft_UART_Write(13);
Send_PCF(Calc_Err());
}
//*/
}
SI quelqu'un sais pourquoi , qu'il me fasse signe .
Merci.